The
isolated DC/DC converter has enabled countless applications that would not otherwise be possible. Some prominent examples are
medical power supplies, high-speed communication buses, offline power solutions, motor drives, and high-voltage use cases.
Additionally, one could argue that the most valuable contribution of isolated DC/DC converters relates to the isolation itself. Being able to SAFELY process high voltages and/or large amounts of power has been a critical contribution of power electronics to society. Many people may not be aware of all of this and therefore do not have an appreciation for these enabling technologies, but I am sure they are happy with the results in their daily lives. As power electronics engineers (or related), we are very much accustomed to being the unsung heroes that “secretly” make all the electronics of the world operate, even if considered “black magic” or unbeknownst to the user.
First, we should define what isolation is and how it applies to DC/DC converters. Electrical (a.k.a. – galvanic) isolation is the physical separation of conductors to prevent the direct flow of current between them [1]. The quickest test for evaluating if any level of isolation is present in a system is to evaluate the ground potentials between two targets. The grounds between isolated circuits should be at independent (a.k.a. floating) potentials. In addition to safety needs, there are several practical uses of floating grounds in DC/DC converters, which will be covered a little later.
Power conversion circuits use many different types, methods, and implementations of isolation, so we shall quickly overview the most salient here. The classification of isolation depends completely on the physical isolation techniques, they are often accomplished in the transformer assembly/construction and by physical spacing. The table below showcases a more comprehensive overview of isolation in DC/DC converters and their implementation.
| Isolation grade class |
Description |
Example use case |
| Functional |
The output is isolated, but there is no protection against electric shock |
Ring Core Transformer with Functional Isolation |
| Basic |
The isolation offers shock protection as long as the barrier is intact |
Bobbin Transformer with Basic Isolation |
| Supplementary |
An additional barrier to basic, required by agencies for redundancy |
Example of a Reinforced Transformer Construction with a Basic and Supplementary Layer of Insulation (shown as the thick black lines in the diagram |
| Reinforced |
A single barrier equivalent to two layers of Basic insulation |
It is very important to note that the requirements and aspects of isolation needs are dictated by many different industrial/
safety standards, which can be highly dependent on the application and/or geographical location of usage. So be sure to capture any safety/certification requirements for your system early in the design process. It is imperative to research the specific requirements of the application at hand as the metrics, spacings (in 2D & 3D), isolation levels, and verification test methodology/setups can vary greatly and often be the difference maker between a smooth development and unexpected cost/time budget overruns. For instance, please see the excerpt below for the voltage spacing requirements of uninsulated conductors from IPC-9592B. While it clearly calls out minimum spacing based on conductor potentials, it also notes that creepage/clearance requirements in a related standard (IEC 60950 in this case) may be more stringent and precedence should be taken. Supporting a medical and/or high-reliability application will also come with many application-specific guidelines/requirements in this regard.
Fig. 1: IPC-9592B Uninsulated Conductor Voltage-Spacing Requirements Excerpt [3]
While isolation is commonly accomplished in transformer construction, it can also be implemented in other ways, particularly for smaller signals (i.e., control feedback, digital communications, etc.). It is very common to isolate communication buses, such as that of CAN-bus in
automotive and
industrial applications by using a small, isolated DC/DC or even capacitive isolation for digital signals. The small-signal feedback information from an isolated power converter’s output can be fed back to the input via an optoisolator. The optoisolator converts a signal’s electrical energy to optical, then back to electrical, thus passing along the critical control info while preserving the galvanic isolation between input and output.
Modern improvements in transformer construction/materials,
3D power packaging (3DPPR) techniques, and other novel geometries and manufacturing processes have made great strides in this space. Higher levels of reinforced insulation along with improved assembly techniques enable a design to meet isolation requirements, while still shrinking the overall size of the solution and utilizing the benefits of more automated manufacturing processes. This enhances overall quality and reliability, while concurrently taking advantage of economies of scale so that the robustness and power density improvements do not come at the detriment of cost. A prime example is how previously manually-wound toroids are now automatically controlled by implementing a planar structure that embeds windings in printed circuit boards (PCB) and directly incorporates the magnetic core materials into the surrounding geometry.
