RVPW015 Series

  • Suitable for PSR and SSR flyback/Boost/Buck
  • PSR Feedback Minimum Sampling Time as Low as 0.4us
  • CCM and DCM Modes are Compatible
  • Integrated 132V/0.6Ω LDMOS
  • Integrated Lossless Current Sampling
  • Programmable Peak Current
  • Programmable Power MOSFET Driving Speed
  • Programmable Input Undervoltage and Overvoltage Protection
  • Short Circuit Protection, and Over Temperature Protection
  • Linearly Decrease of the Operating Frequency to Optimize Efficiency under Light-load Conditions
  • Internal Feedforward Compensation Function
  • Internal Soft Start and Slope Compensation
  • Internal PSR Loop Control in CCM/DCM Mode
  • Direct Optocoupler Interface
  • Internal Loop Compensation and Output Diode Voltage Drop Temperature Compensation
  • ESOP8 Strong Heat Dissipation Packaging

RVPW015 is a highly integrated power control IC designed to support multiple power supply topologies, including Flyback, Boost, and Buck converters. It is compatible with various output voltage feedback methods such as Secondary-Side Regulation (SSR), Primary-Side Regulation (PSR), and resistive voltage divider feedback. PSR operation is supported at switching frequencies up to several hundred kHz. The internal output voltage sampling circuit is capable of operating in both Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM), with a sampling time window requirement as short as 400ns. An integrated loop compensation circuit with fast dynamic response ensures excellent loop stability and rapid transient performance for the switching power supply. RVPW015 incorporates multiple control and protection functions, while requiring only minimal external components. It offers flexible design capabilities through configurable external resistors. A single resistor can be used to implement startup, feedforward compensation, and programmable turn-off speed control of the internal power MOSFET. Another resistor allows for programming the peak current of the power MOSFET, enabling a “lossless” current sensing method. With just two resistors, both input undervoltage protection (UVP) and input overvoltage protection (OVP) thresholds can be independently defined. The RVPW015 also integrates comprehensive protection features, including overload protection (OLP), output short-circuit protection (SCP), output overvoltage protection (OVP), and over-temperature protection (OTP). Once a fault condition is cleared, the chip automatically recovers, enhancing system robustness and maximizing the reliability of the power supply.

  Part Number Power (W) Vin (V) Vout 1 (V) Iout 1 (mA) Isolation (kV)
1 RECOM | RVPW015-FJ2-CT | IC, SMD
Focus New
4 - 80
2 RECOM | RVPW015-FJ2-R | IC, SMD
Focus New
4 - 80

Solutions based on this IC/Transformer combination (available board mounted or as individual components)

  Part Number Power (W) Isolation (kV) Vin (V) Main Vout (V) Primary IC Transformer Secondary IC
1
New
6 1.5 18 - 75 5
Attributes RVPW015
Product Category IC
Vin (V) 4 - 80
Main Vout (V) 2 to 999
Output Voltage Range (V) 2 - 999
MAX Iout (mA) 2
Mounting Type SMD
Package Style ESOP-8
Length (mm) 5
Width (mm) 6.2
Height (mm) 1.7
MIN Operating Temp (°C) -40
MAX Operating Temp (°C) 125
Protections OCP, OTP, OVP, UVLO
Directives Halogen-free, REACH, RoHS 2+ (10/10)
Operating Modes Current Mode
Warranty 1 Year
Config 1 Channel
Topology Flyback
Number of Phases 1
MAX Duty Cycle (%) 80
Functional Features Enable, Variable Switching Frequency
MIN Switching Frequency (kHz) 9
MAX Switching Frequency (kHz) 330
MIN Storage Temperature (°C) -55
MAX Storage Temperature (°C) 150
  Part Number Power (W) Vout 1 (V) Vin (V) Mounting Type
1 RECOM | RVPW015-FJ2-CT | IC, SMD
Focus New
4 - 80 SMD
2 RECOM | RVPW015-FJ2-R | IC, SMD
Focus New
4 - 80 SMD
Important parameters include input voltage range, output voltage, maximum load current, switching frequency, efficiency, size, and thermal performance. Selection involves balancing these factors to meet the specific requirements of your application, ensuring the IC operates within its safe thermal and electrical limits while minimizing PCB space.
A boost converter increases the input voltage to a higher output voltage using an inductor, low-side switch, a rectifier, and output filter.
A buck converter reduces the input voltage to a lower output voltage using a high-frequency high-side or low-side switch, an inductor, a rectifier, and output filtering.
A buck‑boost converter can both increase and decrease the output voltage in relation to the input voltage using one or more inductors, a high-side or a low-side switch, rectifiers, and output filtering.
A DC/DC controller IC manages the switching behavior of external power components such as MOSFETs, inductors, and transformers.
A DC/DC converter IC converts one DC voltage level to another using switching techniques and integrated control circuitry.
A synchronous converter replaces the traditional rectifier diode with a MOSFET, which reduces conduction losses and significantly improves efficiency.
An asynchronous converter uses a diode as the rectification element, resulting in a simpler design but typically lower efficiency compared to synchronous alternatives.
A converter IC typically integrates the power switches internally, providing a more compact solution. In contrast, a controller IC manages the switching behavior of external power components such as MOSFETs, inductors, and transformers.
Buck-boost converters are commonly used when the input voltage can vary above and below the desired output voltage. For example, this topology is ideal for maintaining a 12V fixed voltage from a 12V battery supply, where the battery level may fluctuate during discharge or charging.
Push-pull and full bridge topologies are often unregulated, making them best suited for use with regulated input voltage rails. Push-pull is preferred for 3.3V and 5V input voltage rails because the input current is shared between the switching transistors, allowing more power to be extracted from a smaller IC package. Full Bridge is preferred for 5V up to 24V input voltage rails because the input voltage stress is shared between the switching transistors, enabling it to efficiently switch higher input voltages. For regulated output voltages, wider input voltage ranges, or higher output power applications, Flyback is the preferred topology due to its versatility and ability to provide galvanic isolation.
Power ICs enable efficient switching topologies, optimized control algorithms, and fast switching frequencies that minimize power losses.
Key advantages include high integration, a small footprint, and improved efficiency. Integrated power ICs allow designers to create optimized power solutions tailored specifically for unique applications.
Power ICs typically require more external components and careful PCB design. This requirement for additional external parts and complex layout increases overall development complexity.
Common types include DC/DC converter ICs, PWM controller ICs, gate driver ICs, PMICs, linear regulators, and battery management ICs.
Power ICs are used in industrial electronics, telecom systems, consumer electronics, automotive systems, and IoT devices.
A power IC (power integrated circuit) is a semiconductor device designed to regulate or convert electrical power. It integrates essential functions such as feedback regulation, switching control, protection, and power management into a single chip.
A PMIC is an integrated circuit designed to manage power distribution within complex electronic systems. It typically integrates multiple voltage regulators, power sequencing, battery management, and system monitoring functions into a single semiconductor device.
A power IC is a semiconductor controller chip that requires external magnetic components such as inductors or transformers but often includes integrated power switching transistors. A power module integrates many of these discrete components into a single packaged solution, simplifying PCB design and reducing overall development time.
Power switching transistors differ primarily in how they are controlled, their switching speed, maximum switching voltage, and their power-handling limits. The main types include MOSFETs (up to 100kHz, 600V, 1kW), SiCs (up to 500kHz, 3.3kV, 100kW), GaNs (up to 1MHz, 900V, 10kW), and IGBTs (up to 50kHz, 6.5kV, 1MW).

MOSFETs are most often used in switching power supplies due to their low cost and ease of integration. SiCs and GaNs are utilized for high-frequency switching applications, while IGBTs are preferred for very high power or high-voltage switching.
Power ICs are often utilized when designers require maximum flexibility, lower cost at high volumes, or highly customized power architectures.